DMG Honigum Putty With Light Body

DMG Honigum Putty + Light Body Kit
In stock
Quick Overview
  • Short time in mouth.
  • High patient comfort.
  • Reduced micro movements.
Special Price $139.00 was $200.00

DMG Honigum Putty + Light Body Kit

Honigum-Putty offers extraordinary recovery after deformation thus facilitating a precise reproduction of the oral situation. A precise detail reproduction is guaranteed. Thanks to the DMG-developed Snap-Set technology the new Honigum-Putty offers a so far unrivaled combination of comfortable working time and short time in mouth. Its generous working time reduces the »mix stress« to a minimum. Deformations due to already set material are prevented, and micro movements are reduced by the quicker cross linking. For the patient the shorter time in mouth translates into significantly more comfort during the treatment.

Honigum-Putty is an impression material based on addition curing silicones. The material is available as a hand-mix version and in the ready-to-use pre-filled MixStar cartridge, which is suitable for use in the DMG MixStar-eMotion and other commercially available mixing machines.


  • Vinyl polysiloxanes.
  • Hydrogen polysiloxanes.
  • Silicium dioxide.
  • Pigments.
  • Additives.
  • Platinum catalyst.

Double-mix impressions

  • Fill the tray with Honigum-Putty.
  • Syringe the preparation with Honigum-Light. Observe the associated instructions for use! Note: The filling of the tray and syringing should be completed at the same time as the higher temperature in the mouth leads to a quicker setting of the syringed material compared to the tray material. 3. Position the filled tray in the mouth within the working time, slowly and using very little force, and allow the impression to form. 4. Remove the impression from the mouth once the setting time has elapsed.


Crown and bridge impressions.
Inlay and onlay impressions.


  • Unique Snap-Set technology (long working time and short time in mouth).
  • Excellent recovery after deformation.
  • Excellent dimensional stability.
  • Prevents mixing stress.
  • No premature setting of the material.
  • Short time in mouth.
  • High patient comfort.
  • Reduced micro movements.
  • Excellent recovery after deformation.
  • Highest precision.


  • Using the MixStar cartridge in the DMG MixStar-eMotion
  • Slide the locking mechanism upwards in order to open the cartridge. Do not remove the locking mechanism from the cartridge
  • Remove the cap from the cartridge and discard. Attach a new mixing tip.
  • Secure the mixing tip by sliding the locking mechanism into the locked position.
  • Insert the cartridge into the MixStar-eMotion. A brief acoustic signal confirms the correct insertion of the cartridge.

Changing the mixing tip

  • Slide the locking mechanism upwards.
  • Remove the old mixing tip and any hardened material blocking the cartridge openings
  • Place the mixing tip securely on the respective cartridge opening. Note: In order to attain an optimum mixing result, DMG recommends the use of the mixing tips available from DMG. All mixing tips are also available as refill packs
  • Lock the mixing tip in place with the locking mechanism

Using the hand-mix system

  • Take equal amounts of the base paste and the catalyst paste out of the container, always using the colored spoon for the base paste and the white spoon for the catalyst paste.
  • Mixing: At room temperature, knead the base and catalyst pastes in a ratio of 1:1 with the finger tips for 30 seconds, until the color is homogenous.
  • Reseal the container immediately after use! Do not mix up the container lids!


  • 2 x 450ml Soft Putty.
  • 2 x 450ml Light Body (Dispensing Gun & Tips Compatibility: 1:1).
More Information
Return Policy Not Accepted
Viscosity Light Body, Putty
Type Of Silicone Addition Silicone
Write Your Own Review
You're reviewing:DMG Honigum Putty With Light Body
Your Rating
  • 2 x 450ml Soft Putty.
  • 2 x 450ml Light Body (Dispensing Gun & Tips Compatibility: 1:1).